Forum.hr

Natrag   Forum.hr > Informatička tehnologija > Softver
Korisničko ime
Lozinka

Softver O programima koje koristite ili namjeravate koristiti

Odgovor
 
Tematski alati Opcije prikaza
Old 17.09.2012., 13:44   #1
grocky
Registrirani korisnik
 
Registracija: Jul 2010.
Postova: 916
Koliko je vremenski radio racunar - program za to

Imao sam nekad davno program koji je ocitavao koliko je HDD radio, i po tome sam znao koliko je vremenski i moj racunar radi. E sad se ne mogu sjetiti naziva programa, pa da mi neko pomogne

Da li postoji samo za info o radu HDD ili ima nesto opcenito povezano za rad i maticne i proc.....

Treba da dobijem jedan laptop iz Amerike, pa zelim da provjerim da li je koristen i koliko.
grocky is offline  
Odgovori s citatom
Old 17.09.2012., 17:52   #2
ssgtmoler
Hardcore Gamer
 
ssgtmoler Avatar
 
Registracija: Feb 2012.
Lokacija: Slavonski Brod
Postova: 249
Google čini čuda
__________________
Cathedra mea, regulae meae
ssgtmoler is offline  
Odgovori s citatom
Old 22.09.2012., 09:18   #3
drGspot
Registrirani korisnik
 
Registracija: Aug 2005.
Lokacija: zagreb
Postova: 60
Quote:
grocky kaže: Pogledaj post
Imao sam nekad davno program koji je ocitavao koliko je HDD radio, i po tome sam znao koliko je vremenski i moj racunar radi. E sad se ne mogu sjetiti naziva programa, pa da mi neko pomogne

Da li postoji samo za info o radu HDD ili ima nesto opcenito povezano za rad i maticne i proc.....

Treba da dobijem jedan laptop iz Amerike, pa zelim da provjerim da li je koristen i koliko.
u unixima/GNU/Linuxu zanimljia je komanda:

uptime <enter>

**********
gxxxx@g-Sxxxx-nxxxe ~ $ uptime
10:03:42 up 2 min, 1 user, load average: 0.47, 0.46, 0.20

(apropo vremena cijelog sustava)
*************
hdparm daje dosta info-a o disku, da vidimo da li i o vremenima...:

******
hdparm - get/set hard disk parameters - version v9.37, by Mark Lord.

Usage: hdparm [options] [device ...]

Options:
-a Get/set fs readahead
-A Get/set the drive look-ahead flag (0/1)
-b Get/set bus state (0 == off, 1 == on, 2 == tristate)
-B Set Advanced Power Management setting (1-255)
-c Get/set IDE 32-bit IO setting
-C Check drive power mode status
-d Get/set using_dma flag
-D Enable/disable drive defect management
-E Set cd/dvd drive speed
-f Flush buffer cache for device on exit
-F Flush drive write cache
-g Display drive geometry
-h Display terse usage information
-H Read temperature from drive (Hitachi only)
-i Display drive identification
-I Detailed/current information directly from drive
-k Get/set keep_settings_over_reset flag (0/1)
-K Set drive keep_features_over_reset flag (0/1)
-L Set drive doorlock (0/1) (removable harddisks only)
-m Get/set multiple sector count
-M Get/set acoustic management (0-254, 128: quiet, 254: fast)
-n Get/set ignore-write-errors flag (0/1)
-N Get/set max visible number of sectors (HPA) (VERY DANGEROUS)
-p Set PIO mode on IDE interface chipset (0,1,2,3,4,...)
-P Set drive prefetch count
-q Change next setting quietly
-Q Get/set DMA queue_depth (if supported)
-r Get/set device readonly flag (DANGEROUS to set)
-R Obsolete
-s Set power-up in standby flag (0/1) (DANGEROUS)
-S Set standby (spindown) timeout
-t Perform device read timings
-T Perform cache read timings
-u Get/set unmaskirq flag (0/1)
-U Obsolete
-v Use defaults; same as -acdgkmur for IDE drives
-V Display program version and exit immediately
-w Perform device reset (DANGEROUS)
-W Get/set drive write-caching flag (0/1)
-x Obsolete
-X Set IDE xfer mode (DANGEROUS)
-y Put drive in standby mode
-Y Put drive to sleep
-z Re-read partition table
-Z Disable Seagate auto-powersaving mode
--dco-freeze Freeze/lock current device configuration until next power cycle
--dco-identify Read/dump device configuration identify data
--dco-restore Reset device configuration back to factory defaults
--direct Use O_DIRECT to bypass page cache for timings
--drq-hsm-error Crash system with a "stuck DRQ" error (VERY DANGEROUS)
--fallocate Create a file without writing data to disk
--fibmap Show device extents (and fragmentation) for a file
--fwdownload Download firmware file to drive (EXTREMELY DANGEROUS)
--fwdownload-mode3 Download firmware using min-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode3-max Download firmware using max-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode7 Download firmware using a single segment (EXTREMELY DANGEROUS)
--idle-immediate Idle drive immediately
--idle-unload Idle immediately and unload heads
--Istdin Read identify data from stdin as ASCII hex
--Istdout Write identify data to stdout as ASCII hex
--make-bad-sector Deliberately corrupt a sector directly on the media (VERY DANGEROUS)
--offset use with -t, to begin timings at given offset (in GiB) from start of drive
--prefer-ata12 Use 12-byte (instead of 16-byte) SAT commands when possible
--read-sector Read and dump (in hex) a sector directly from the media
--security-help Display help for ATA security commands
--trim-sector-ranges Tell SSD firmware to discard unneeded data sectors: lba:count ..
--trim-sector-ranges-stdin Same as above, but reads lba:count pairs from stdin
--verbose Display extra diagnostics from some commands
--write-sector Repair/overwrite a (possibly bad) sector directly on the media (VERY DANGEROUS)
************************
http://linux.die.net/man/8/hdparm
*********************
...primjer diagnostike na playstation3 hardu:

http://blog.rot13.org/2009/09/playst...for_linux.html
drGspot is offline  
Odgovori s citatom
Sponsored links
Advertisement
 
Advertisement
Odgovor


Tematski alati
Opcije prikaza

Pravila postanja
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smajlići su On
[IMG] kôd je On
HTML kôd je Off





Sva vremena su GMT +1. Trenutno vrijeme je: 05:11.



Powered by vBulletin Version 3.8.4 (hrvatski)
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Site content ©1999-2009 Forum.hr
Ad Management by RedTyger